Magnetic Field Shielding Laminated Foil Yshield M2A 0,12 MM

| M2A is a super-thin magnetic field shielding foil for magnetic fields isolation. For this product, we have bonded 2 layers of high-tech magnetic field shielding film.

| The underside is protected with laminating film and we use aluminum as the surface, which is why the film is also ideal for high-frequency shielding.

| Suitable for small areas in the domestic environment, in electronics, as well as for large areas in construction, trade or industry.

| The roll length of 100 meters is particularly advantageous on large surfaces for efficient laying. It can also be used in a wide range of applications in cars, electric cars, vans, motorhomes and caravans.

Technical Data

• Width: 21 cm (shielding surface); 23 cm (total product)

• Length: Available by the meter (linear meter l.m = 1 Ut.) / 100 meter rolls
• Thickness: 0.12 mm
• Attenuation high frequency: 125 dB.
• Attenuation magnetic fields (Three-phase 50Hz): 1 layer: 12,1 dB (75,1 %) | 2 layers: 16,3 dB (84,7 %) | 3 layers: 19,5 dB (89,4 %) | 4 layers: 21,7 dB (91,8 %)
  
• Attenuation magnetic fields (Single-phase 50 Hz): 1 layer: 10,5 dB (70,1 %) |2 layers: 13,3 dB (78,3 %) | 3 layers: 16,0 dB (84,1 %) | 4 layers: 18,6 dB (88,2 %)
  
• Shielding magnetic field (static): DC consumers, earth's magnetic field, permanent magnets are only shielded in a relevant manner with very many layers.

• Minimum bending radius: 10 mm.

• The high-tech material has a high initial permeability and high saturation induction from 5 Hz to 100 kHz.

Processing

• Attention: The M2A-series can be cut with high-quality scissors! The cutting edges are as sharp as knives and need to be protected (e.g. with fabric tape) immediately after cutting! Use cut-resistant gloves during processing! We recommend planning the installation of the plates in a way that you do not have to cut them! Pay attention with larger wall spaces that the plates are a water vapour barrier.
• Application: Choose an adhesive that can bond the laminating film made of PET (polyethylene terephthalate). There are high viscosity mounting adhesives for e.g. solid substrates or flexible plastic adhesives for gluing, e.g. underneath carpets in cars. Follow the instructions of the glue manufacturer. >> Non-absorbent substrates or multiple layers can be problematic because the solvent cannot dry out due to the vapor-tight film. For this reason, we recommend our own adhesive YSHIELD® PSA, which forms a self-adhesive layer after application and drying

• Application using a stapler or nailer: If the substrate is suitable, we recommend using an electric stapler or nailer. For one layer including overlap, a medium-priced electric tacker is sufficient; for two or more layers, you will need a professional nailer. The shielding surface must overlap by at least 2 cm.
• Multilayer installation: Always install the plates in an offset position - the surface is to cover the overlapping underneath.
• High-frequency shielding: The aluminum top side provides excellent shielding against high-frequency fields. To do this, the sheets must overlap by 3 cm. As the laminating foil on the underside creates a thin gap despite the overlap, we recommend the use of our shielding tape HNX50.

Grounding

This product with an electrically conductive surface has to be integrated into the functional-equipotential bonding (FEB). Please find suitable grounding accessories under "Grounding".

Important

Not be performed RETURNS on products CUTTED or MANUFACTURED on demand, only against defects of manufacture.