Magnetic Field Shielding Laminated Foil Yshield M2L 0,12 MM

| M2L is a super-thin magnetic field shielding foil for magnetic fields isolation.For this product, we have bonded 2 layers of high-tech magnetic field shielding film and protected them on both sides with laminating film.

| Highly resistant, suitable as an intermediate layer in roof or floor constructions.

| Suitable for small areas in the domestic environment, in electronics, as well as for large areas in construction, trade or industry.

| The roll length of 100 meters is particularly advantageous on large surfaces for efficient laying. It can also be used in a wide range of applications in cars, electric cars, vans, motorhomes and caravans.

Technical Data

• Width: 21 cm (shielding surface); 23 cm (total product)

• Length: Available by the meter (linear meter l.m = 1 Ut.) / 100 meter rolls
• Thickness: 0.12 mm
• Attenuation magnetic fields (Three-phase 50Hz): 1 layer: 12,1 dB (75,1 %) | 2 layers: 16,3 dB (84,7 %) | 3 layers: 19,5 dB (89,4 %) | 4 layers: 21,7 dB (91,8 %)
  
• Attenuation magnetic fields (Single-phase 50 Hz): 1 layer: 10,5 dB (70,1 %) |2 layers: 13,3 dB (78,3 %) | 3 layers: 16,0 dB (84,1 %) | 4 layers: 18,6 dB (88,2 %)
  
• Shielding magnetic field (static): DC consumers, earth's magnetic field, permanent magnets are only shielded in a relevant manner with very many layers.

• Minimum bending radius: 10 mm.

• The high-tech material has a high initial permeability and high saturation induction from 5 Hz to 100 kHz.

Processing

• Attention: The M2L-series can be cut with high-quality scissors! The cutting edges are as sharp as knives and need to be protected (e.g. with fabric tape) immediately after cutting! Use cut-resistant gloves during processing! We recommend planning the installation of the plates in a way that you do not have to cut them! Pay attention with larger wall spaces that the plates are a water vapour barrier.
• Application: Choose an adhesive that can bond the laminating film made of PET (polyethylene terephthalate). There are high viscosity mounting adhesives for e.g. solid substrates or flexible plastic adhesives for gluing, e.g. underneath carpets in cars. Follow the instructions of the glue manufacturer. >> Non-absorbent substrates or multiple layers can be problematic because the solvent cannot dry out due to the vapor-tight film. For this reason, we recommend our own adhesive YSHIELD® PSA, which forms a self-adhesive layer after application and drying

• Application using a stapler or nailer: If the substrate is suitable, we recommend using an electric stapler or nailer. For one layer including overlap, a medium-priced electric tacker is sufficient; for two or more layers, you will need a professional nailer. The shielding surface must overlap by at least 2 cm.
• Multilayer installation: Always install the plates in an offset position - the surface is to cover the overlapping underneath.

Grounding

When shielding magnetic fields, also pay attention to the electric fields. Grounding must be carried out to prevent the spread of electric fields. The M2L series is fully laminated, but there is still a solution for contacting: Stick our GSX10 or GSX50 grounding tape to all surfaces. Staple or nail through the grounding tape. The staples or nails make contact with the panel and grounding strap. Further components can be found under "Grounding".

Important

It's a manufactured or cutted on-demand item. We recommend that customers be sure QUANTITY and TYPE of material carefully before ordering !!! Not be performed RETURNS on products CUTTED or MANUFACTURED on demand, only against defects of manufacture.