Magnetic Shielding Sheet Yshield M6L 0,5 MM

| M6L is a magnetic field shielding plate for magnetic fields isolation, permanently protected from environmental influences on both sides with a laminating film | It is therefore extremely durable, and can be used e.g. on a flat roof or under floor structures | Single-layer processing has the best price/performance ratio | For higher magnetic flux densities, multi-layer processing is required | We have connected 6 very thin shielding foils together, because several thin layers provide better shielding than one thick sheet | It is suited for small surfaces in a domestic environment, as well as for large surfaces in construction, trade or industry | Additionally there are various application possibilities in cars, electric vehicles, vans, mobile homes, campers.

Technical Data

• Sizes: [M6L-32] 29 x 21 cm (protective surface); 31 x 23 cm (total) |[M6L-82] 80 x 21 cm (protective surface); 82 x 23 cm (total) |[M6L-85] 80 x 55 cm (protective surface); 82 x 57 cm (total).
  
• Thickness: 0.5 mm
• Attenuation magnetic fields (Three-phase): Single-layer 19.2 dB (89.0 %), two-layer 25.7 dB (94.8 %), three-layer 28.9 dB (96.4 %), four-layer 31.8 dB (97.4 %)
• Attenuation magnetic fields (Single-phase): Single-layer 17.3 dB (86.3 %), two-layer 22.0 dB (92.0 %), three-layer 25.3 dB (94.6 &), four-layer 27.6 dB (95.8 %)
• Attenuation magnetic fields (Static): DC consumers, earth magnetic field, permanent magnets are shielded in a range from 15% (1-layer) to 58% (4-layer).
• Corrosion resistance: Corresponds to that of aluminum
• Minimum bending radius: 20 cm

• The high-tech material has a high initial permeability and high saturation induction from 5 Hz to 50 kHz.
• In addition, static magnetic fields at 0 Hz are shielded, as are electromagnetic fields up to 40 GHz.

Processing

• Attention: The M6L-series can be cut with high-quality scissors! The cutting edges are as sharp as knives and need to be protected (e.g. with fabric tape) immediately after cutting! Use cut-resistant gloves during processing! We recommend planning the installation of the plates in a way that you do not have to cut them! Pay attention with larger wall spaces that the plates are a water vapour barrier.
• Application: Choose an adhesive that can bond the laminating film made of PET (polyethylene terephthalate). There are high viscosity mounting adhesives for e.g. solid substrates or flexible plastic adhesives for gluing, e.g. underneath carpets in cars. Follow the instructions of the glue manufacturer.
• Application using a stapler or nailer: If the substrate is suitable, we recommend using an electric stapler or nailer. For one layer including overlap, a medium-priced electric tacker is sufficient; for two or more layers, you will need a professional nailer. The shielding surface must overlap by at least 2 cm.
• Multilayer installation: Always install the plates in an offset position - the surface is to cover the overlapping underneath.

Grounding

When shielding magnetic fields, also pay attention to the electric fields. Grounding must be carried out to prevent the spread of electric fields. The M6L series is fully laminated, but there is still a solution for contacting: Stick our GSX10 or GSX50 grounding tape to all surfaces. Staple or nail through the grounding tape. The staples or nails make contact with the panel and grounding strap. Further components can be found under "Grounding".

Important

It's a manufactured or cutted on-demand item. We recommend that customers be sure QUANTITY and TYPE of material carefully before ordering !!! Not be performed RETURNS on products CUTTED or MANUFACTURED on demand, only against defects of manufacture.